Can You Put Pet Hair in Resin? What Works and What Doesn't

Yes — you can put your pet's hair in resin, and it is one of the most popular ways to turn fur into jewelry or a small keepsake. But hair behaves differently from dried flowers or glitter. A few simple steps make the difference between a clear, beautiful result and a cloudy one full of bubbles.

The short answer: use clean, completely dry hair, seal it lightly before you add it, use a thin resin made for jewelry, and work slowly to avoid trapping air.

Why hair needs a little extra care

Fur is fine, fluffy and full of tiny pockets of air. Drop a loose tuft straight into resin and two things tend to happen: air escapes from the fur as bubbles, and the hair floats or spreads out in ways you did not plan. Moisture in the hair can also cause cloudiness. That is why preparation matters.

Step 1: Prepare the hair

  • Clean and dry. Make sure the hair is clean and completely dry. See our guide on how to save and store your pet's fur.
  • Seal it. One well-known resin tutorial suggests attaching a tuft to clear tape and misting it with a couple of light coats of clear spray sealant on each side. Sealing helps keep air and moisture locked out of the hair.
  • Decide on the look. Loose hair gives a soft, wispy look. Hair that is gathered or lightly glued into shape gives a neater, more defined look.

Step 2: Choose the right resin

For small jewelry pieces, a thin, low-viscosity jewelry resin is usually the best choice. It flows into small molds and around the hair more easily, which means fewer bubbles. Thick resin is harder to work into tiny cavities without trapping air.

There are two common types:

  • UV resin cures in minutes under a UV lamp. It is handy for small pieces and thin layers.
  • Two-part epoxy resin is mixed from two components and cures over hours. It is often used for larger or deeper pieces.

Always follow the instructions and safety guidance from the resin manufacturer, work in a ventilated space and wear gloves.

Step 3: Work in layers

  1. Pour or dot a thin first layer of resin into the mold and let it cure partly or fully, depending on your resin.
  2. Place the hair on top, arranging it the way you want it to look.
  3. Cover it with another thin layer, pressing gently so the hair is fully coated.
  4. Add a final layer to fill the mold and give a smooth, glossy finish.

Working in layers gives you more control over where the hair sits, and it makes bubbles easier to spot and remove.

How to avoid bubbles and cloudiness

  • Use sealed, dry hair. This is the biggest single factor.
  • Pour slowly and in thin layers.
  • Pop surface bubbles with a toothpick before the resin cures.
  • Work at room temperature. Cold resin is thicker and traps more air.

Will it last?

Hair that is fully sealed inside cured resin is protected from air and moisture, which is what makes resin such a good material for keepsakes. Like all resin jewelry, it lasts best when you keep it away from harsh chemicals, long soaks in water and strong heat.

Making it yourself

Many people find that making the piece themselves becomes part of remembering their pet. We are building DIY kits with everything you need to make petite, wearable jewelry with your pet's hair — step by step. Join the list for early access below.

Looking for other ideas? See 10 keepsake ideas for your pet's fur.

Frequently asked questions

Can you put dog or cat hair in resin?
Yes. Dog, cat and horse hair can all be set in resin. Make sure the hair is clean, dry and ideally sealed first.

Why does my resin go cloudy with hair in it?
Usually because of moisture or air in the hair. Drying and sealing the hair before adding it helps.

What kind of resin is best for pet hair jewelry?
A thin, low-viscosity jewelry resin is usually easiest for small pieces, because it flows around the hair with fewer bubbles.

How much hair do I need?
Only a few strands for most jewelry.

Back to blog